There are 59 products.
Active filters
1702747 A&R Seal Kit 2747 for 3 pistons, Pump XM, Series X-Pro, 9, 178
Consists of:
-O-ring X3
-Low pressure (suction) seal X3
-High pressure seal X3
-Seal kit for 3 pistons
Suttner Pressure Switch ST-7.1 BLACK 40 bar/580 psi for Pressure Washer. Made in GERMANY.
SPECIFICATION:
-Operating (start up) pressure: 40 bar/ 580 psi
-Rated pressure: 300bar/ 4350psi
-Rated temperature: 90C/ 194F
-Max Voltage: 250V
-Max Current strength: 10.1A
-Electrical Insulation rating: 65 IP
-Material: Brass
-Color: Black
-Inlet: 1/4” M
-Cable length: 950mm/ 37 Inches
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 06
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel
Suttner ST-6 Flow Switch, All position (Horizontal or Vertical) Spring assisted brass magnet. Made in Germany
FEATURES:
-Horizontal or vertical mount
-Easy brass reed switch replacement.
SPECIFICATION:
-Max. Pressure: 5,070 PSI/350 bar.
-Min. Pressure: 75 PSI
-Max. Flow Rate: 8 GPM/ 30 ltr.
-Min. Flow Rate: 1 GPM
-Max Voltage: 250 V
-Max Current: 1 Amps
-Max: Fluid Temperature: 180° F/ 80 ° C
-Cable Length: 47.0 in/ 1200 mm.
-Inlet & Outlet: 3/8 MNPT
-Housing: Forged Brass
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 055
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel
Flow Switch ST-7 1.5L/Min open 0.4 GPM
ST-7 Flow switch with micro-switch. Switch-on point 0.4 GPM. Mounts in any position horizontal or vertical.
SPECIFICATION:
-Maximum pressure: 5000 psi
-Minimum flow rate: 0.4 GPM
-Maximum flow rate: 12 GPM
-Temperature: 176°F
-Input : 3/8 F
-Outlet: 3/8 F
-Housing: Brass
-Brass reed switch cord length: 47"
-Contact: 10A-250 V
-International protection rating: IP 65
ST-10 is 2 component nozzle protector. Made out of hard plastic and soft edge protecting sensitive surfaces against damage . Stainless steel body. The nozzle protector suitable for cold and hot water applications in the car wash, agriculture, food industry. ST-10 is unimpeachable, protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/8" M NPT.
Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/8 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge
P.A. Unloader pressure Regulation valve VB 85/280 Blue Spring, knob is not included.
SPECIFICATION:
-Maximum pressure: 4500 psi
-Working rated pressure: 4050 psi
-Inlet 1/2" F
-Outlet 1/2" F
-Bypass 1/2" F
-Maximum flow rate: 21 GPM
-Rated temperature: 195°F
-Housing: forged brass
-Material: brass
-Manufacturer: PA
Nozzle protector. It's made out of soft Rubber which protects sensitive surfaces against damage. It also has a zinc-plated body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 5800 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Zinc-plated steel
Protection material: Rubber
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Zinc-plated steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 5800 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Zinc-plated steel
Protection material: Hard plastic/Soft edge
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Stainless steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge
