P.A. Unloader pressure Regulation valve VB 85/280 Blue Spring, knob is not included.
SPECIFICATION:
-Maximum pressure: 4500 psi
-Working rated pressure: 4050 psi
-Inlet 1/2" F
-Outlet 1/2" F
-Bypass 1/2" F
-Maximum flow rate: 21 GPM
-Rated temperature: 195°F
-Housing: forged brass
-Material: brass
-Manufacturer: PA
Flow Switch ST-7 1.5L/Min open 0.4 GPM
ST-7 Flow switch with micro-switch. Switch-on point 0.4 GPM. Mounts in any position horizontal or vertical.
SPECIFICATION:
-Maximum pressure: 5000 psi
-Minimum flow rate: 0.4 GPM
-Maximum flow rate: 12 GPM
-Temperature: 176°F
-Input : 3/8 F
-Outlet: 3/8 F
-Housing: Brass
-Brass reed switch cord length: 47"
-Contact: 10A-250 V
-International protection rating: IP 65
Foam injector lance with regulator and bottle. The new LS3, now with vertical nozzle. Nozzle size 1.25.
Inlet 1/4 Bsp F
Pressure 160 bar - 16 MPa - 2300 psi
Permissible Pressure 180 bar - 18 MPa - 2600 psi
Rated Flow Rate 12 l/min - 3.2 USGpm
Rated Temperature 60 °C - 140 °F
Tank 1 L - 0.264 USg
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 3/8. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 4”-8” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
The ST-2300 is a professional high pressure cleaning gun (hot/cold water). The grip housing is from an impact-resistant plastic. The valve body and connectors are both corrosion-resistant. The trigger is equipped with a safety lock and rotating swivel joint that the high pressure hose cannot be turned so as to unscrew the connection between high pressure hose and spray gun a swivel joint may be used. By means of this swivel joint the gun may be turned slightly when in an unpressured state in relation to the hose. With increasing pressure the swivel joint becomes increasingly difficult to turn.
Maximum pressure: 4500 psi
Recommended pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: swivel 3/8 F
Outlet: connector 1/4 F
Housing: forged brass
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 05
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
Suttner ST-2300 Professional Pressure Washer Trigger Gun
New Professional, heavy duty, German made, Suttner ST-2300 pressure washer trigger gun. Comes with a 1/4” Female outlet and a heavy duty 3/8’’ Female inlet
SPECIFICATION:
-Maximum Pressure: 4500Psi/ 310 Bar
-Maximum Flow: 12 gal/min/ 45 Ltr/min
-Maximum Temperature: 300F/ 150C Degrees
-3/8" FNPT Inlet
-1/4" FNPT Outlet
-Safety Lock Feature
-Forged brass housing for maximum strength
-Handle constructed of impact resistant plastic
Interpump/General pump Valve Kit 123 for pumps EZ, PP, TC, TP, TX.
Consists of:
Water intake suction foot filter ST-35. High flow suction strainer ideal for tank transfer or agricultural markets. Made in Germany.
SPECIFICATION:
-Without Check valve
-Stainless steel spring and screen
-Inlet Stepped 3/4"-1”, 19-25 mm/ hose barb
-Corrosion-resistant heavy impact resistant plastic
-Max temperature: 140°F
-Compatible with all pressure washers
-Brass weighted to hold onto bottom of tank
Suttner ST-6 Flow Switch, All position (Horizontal or Vertical) Spring assisted brass magnet. Made in Germany
FEATURES:
-Horizontal or vertical mount
-Easy brass reed switch replacement.
SPECIFICATION:
-Max. Pressure: 5,070 PSI/350 bar.
-Min. Pressure: 75 PSI
-Max. Flow Rate: 8 GPM/ 30 ltr.
-Min. Flow Rate: 1 GPM
-Max Voltage: 250 V
-Max Current: 1 Amps
-Max: Fluid Temperature: 180° F/ 80 ° C
-Cable Length: 47.0 in/ 1200 mm.
-Inlet & Outlet: 3/8 MNPT
-Housing: Forged Brass
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 045
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 055. Female 1/4. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Without centric hole, very good cleaning effect due to rotating nozzle jets.
ST-49 non-rotating sewer cleaning Grease ball nozzle. Female 1/4 8x06R. Ss hardened. Made in Germany
The Grease ball features 8 rear jets (0.6 mm) for extreme thrust and highest wall coverage of the pipe. Designed for the ability to clean grease off the sidewall of pipes but has proven to be great on root chokes too. Completely spherical shape. Nozzle drilling as stepped bore for best protection against mechanical impact. Good for 2”-6” inch lines.
ST-40 Quick Screw Coupling M22fX1,5:3/8 M. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 3/8" M
Housing: brass/plastic
Height 46 mm
ST-49.3 mini rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Hardened Ss. Made in Germany
ST-458.1 Orifice size 06 Red. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-458
Nozzle orifice: 06 Red
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
Suttner ST-85 Stainless Steel 38" molded handle Push and Pull lance. Input 1/4"FPT, outlets 1/4"FPT with nozzle ST-10 protector. High pressure nozzle and side handle is NOT included. Made in Germany.
Especially designed for cleaning of places which are difficult to access such as containers, gutters, roofs, underneath fender walls, under vehicles, and heavy equipment. Lance variable adjustment of spraying angle from 20° to 140°. ST-85 Push & Pull lance with nozzle protector ST-10 without high pressure nozzle.
