ST-49 non-rotating sewer cleaning Grease ball nozzle. Female 1/4 8x06R. Ss hardened. Made in Germany
The Grease ball features 8 rear jets (0.6 mm) for extreme thrust and highest wall coverage of the pipe. Designed for the ability to clean grease off the sidewall of pipes but has proven to be great on root chokes too. Completely spherical shape. Nozzle drilling as stepped bore for best protection against mechanical impact. Good for 2”-6” inch lines.
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Stainless steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 7250 psi Rated temperature: 300°F Input: 1/4 F NPT Outlet: 1/4 F NPT Housing: Stainless Steel Protection material: Hard plastic/Soft edge
Nozzle protector. It's made out of soft Rubber which protects sensitive surfaces against damage. It also has a zinc-plated body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 5800 psi Rated temperature: 300°F Input: 1/4 F NPT Outlet: 1/4 F NPT Housing: Zinc-plated steel Protection material: Rubber
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Suttner ST-54 Stainless Steel 38" Molded Handle,Twin lance. 15 degrees bended input 1/4"MPT, 2 outlets 1/4"F with nozzle ST-10 protector and low pressure nozzle. High pressure nozzle is NOT included. Made in Germany. For use when high and low pressures are needed.
For example, spraying cleaning agents with low pressure through an injector valve and then cleaning with high pressure. Lance 15° bended with molded handle, valve ST-54 aside, nozzle protector ST-10 with low pressure nozzle & 1/4" F thread
ST-31 Intake chemical strainer without check valve. Strainer prevents debris from entering and destroying the components. Hose barb 1/4 -1/8. Internal stainless steel weight keep chemical strainer in the bottom of the container.
Housing: plastic Weight: stainless steel Diameter: 20 mm / 0.8" Length: 75 mm / 3"
Pressure regulation valve VB 9 with knob and panel fitting. Brass valve body, stainless steel ball and seat. Hex-shaped non-stick check valve.
Maximum pressure: 3625 psi Working rated pressure: 3200 psi Maximum flow rate: 8 GPM Rated temperature: 195°F Input connector: 3/8 F Outlet: 3/8 F By pass: 3/8 F Pressure gauge outlet: 1/4 F Housing: forged brass
PR-5 Blue pressure switch is a fluid operating electro-mechanical device, which, upon reaching a pre-set (start-up)pressure 15 bar/218 PSI, opens or closes an electrical control contact . Microswitch with very high resistance openings. Considerable resistance to high current values. Compact overall dimension. Three core cable.
Maximum pressure: 5076 psi Rated working pressure: 3650 psi Minimum pressure: 218 psi Temperature: 167°F Input : 1/4 F Housing material: brass Cord length: 37" Max Curr./V. strength Contact: 5A-250 V International protection rating: IP 65
ST-456 Orifice size 05 Black. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-456 Nozzle orifice: 05 black Spray angle 20° Pressure range: 2900 - 5076 psi Inlet: 1/4 "F. Housing: brass Color of protective cap: Black Temperature: 212 °F Spray angle: 20°
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Zinc-plated steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 5800 psi Rated temperature: 300°F Input: 1/4 F NPT Outlet: 1/4 F NPT Housing: Zinc-plated steel Protection material: Hard plastic/Soft edge
