ST-35 Water intake suction foot filter. High flow suction strainer ideal for tank transfer or agricultural markets. Made in Germany.
SPECIFICATION:
-Without Check valve
-Stainless steel spring and screen
-Inlet Stepped 1/2" - 3/4"/13-19 mm/ hose barb
-Corrosion-resistant heavy impact resistant plastic
-Max temperature: 140°F
-Compatible with all pressure washers
-Brass weighted to hold onto bottom of tank
ST-49 non- rotating sewer cleaning root ram nozzle. Nozzle size 06. Female 1/4. Material Ss hardened. Made in Germany
The Root ram is equipped with 3 rear jets (30°) for maximum thrust and 3 additional nozzles (45°) right behind its nose for better cleaning results and wall coverage. The nozzle has proven to be ideal on root chokes. Good for 2"-6" lines.
ST-49.3 mini rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Hardened Ss. Made in Germany
ST-357.1 Orifice size 06 Red. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-357
Nozzle orifice: 06 Red
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 06. Female 3/8. Material Ss and brass. Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 4”-8” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
Valve set for Annovi Reverberi RK Series 138, 228. A&R part number (1389051).Valve kit number 2864.
Consists of:
Quick Screw Coupling (nipple) M22X1,5:3/3"M
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 M
Outlet: 3/8" M
Housing: brass
Height 29 mm
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 045
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
Suttner ST-54 Stainless Steel 38" Molded Handle,Twin lance. 15 degrees bended input 1/4"MPT, 2 outlets 1/4"F with nozzle ST-10 protector and low pressure nozzle. High pressure nozzle is NOT included. Made in Germany. For use when high and low pressures are needed.
For example, spraying cleaning agents with low pressure through an injector valve and then cleaning with high pressure. Lance 15° bended with molded handle, valve ST-54 aside, nozzle protector ST-10 with low pressure nozzle & 1/4" F thread
P.A. Unloader pressure Regulation valve VB 85/280 Blue Spring, knob is not included.
SPECIFICATION:
-Maximum pressure: 4500 psi
-Working rated pressure: 4050 psi
-Inlet 1/2" F
-Outlet 1/2" F
-Bypass 1/2" F
-Maximum flow rate: 21 GPM
-Rated temperature: 195°F
-Housing: forged brass
-Material: brass
-Manufacturer: PA
Annovi Reverberi seal Kit 1857 for 3 pistons Pump RK, RKA, RKV series 138
Consists of:
1701864 A&R valve repair kit 1864 for pump HXM, XT, XM, Ser. Blitz, X-PRO,KB, Hot, 6,7,9, 132, 178 (1269050)
Valve set for Annovi Reverberi HXM, XT,XM Series blitz, KB, x-pro, 6,7,9, 132, 178. A&R part number (1269050). Valve kit number 1864.
Consists of:
-6 Valves
-6 O-rings
ST-458.1 Orifice size 05 Black. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-458
Nozzle orifice: 05 Black
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Stainless steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge
Pressure regulation valve VB-9 with knob, PR-5 switch and panel fitting. Brass valve body, stainless steel ball and seat. Hex-shaped non-stick check valve. Instant pressure response.
Maximum pressure: 3625 psi
Working rated pressure: 3200 psi
Maximum flow rate: 8 GPM
Rated temperature: 195°F
Input connector: 3/8 F
Outlet: 3/8 F
By pass: 3/8 F
Pressure gauge outlet: 1/4 F
Housing: forged brass
Max. Curr. Strenght 6 (2) A
Max. Voltage 250 V
Cord length: 39.4 in
International protection rating: IP 55
Pressure regulation valve VB 9 with knob and panel fitting. Brass valve body, stainless steel ball and seat. Hex-shaped non-stick check valve.
Maximum pressure: 3625 psi
Working rated pressure: 3200 psi
Maximum flow rate: 8 GPM
Rated temperature: 195°F
Input connector: 3/8 F
Outlet: 3/8 F
By pass: 3/8 F
Pressure gauge outlet: 1/4 F
Housing: forged brass
Suttner ST-2600 Pressure Washer Trigger Gun. Patented LTF technology. Inlet 3/8 F, Outlet 1/4 F
Professional, heavy duty, German made, Suttner ST-2600 with patented LTF technology (Low trigger force) pressure washer trigger gun. It comes with a 1/4” female outlet and 3/8 F inlet. Made in Germany.
