ST-49.1 Rotating Sewer Cleaning Nozzle (Nozzle size 06, Female 3/8)

ST-10 is 2 component nozzle protector. Made out of hard plastic and soft edge protecting sensitive surfaces against damage . Stainless steel body. The nozzle protector suitable for cold and hot water applications in the car wash, agriculture, food industry. ST-10 is unimpeachable, protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/8" M NPT.

Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/8 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge

Suttner ST-2600 Pressure Washer Trigger Gun. Patented LTF technology. Inlet 3/8 F, Outlet 1/4 F

Professional, heavy duty, German made, Suttner ST-2600 with patented LTF technology (Low trigger force) pressure washer trigger gun. It comes with a 1/4” female outlet and 3/8 F inlet. Made in Germany.

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 055 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel

PR-5 Black pressure switch is a fluid operating electro-mechanical device, which, upon reaching a pre-set (start-up)pressure 40 bar/580 PSI, opens or closes an electrical control contact . Microswitch with very high resistance openings. Considerable resistance to high current values. Compact overall dimension. Three core cable.

Maximum pressure: 5076 psi
Rated working pressure: 3650 psi
Minimum pressure: 580 psi
Temperature: 167°F
Input : 1/4 F
Housing material: brass
Cord length: 37"
Max Curr./V. strength Contact: 5A-250 V
International protection rating: IP 55

Pressure regulation valve VB 9 with knob and panel fitting. Brass valve body, stainless steel ball and seat. Hex-shaped non-stick check valve.

Maximum pressure: 3625 psi
Working rated pressure: 3200 psi
Maximum flow rate: 8 GPM
Rated temperature: 195°F
Input connector: 3/8 F
Outlet: 3/8 F
By pass: 3/8 F
Pressure gauge outlet: 1/4 F
Housing: forged brass

PA VT-6. Thermal relief valve. Valve bypasses water, reaching the off-temperature. High temperature pump protection valve with copper sonde.

Maximum pressure: 145 psi
Opening Temperature: 145°F
Input : 3/8 M
Output: hose tail 1/4
Housing material: brass

Quick Screw Coupling (nipple) M22X1,5:3/3"M 

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 3/8" M

Housing: brass

Height 29 mm

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 055
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel

Suttner ST-54 Stainless Steel 38" Molded Handle,Twin lance. 15 degrees bended input 1/4"MPT, 2 outlets 1/4"F with nozzle ST-10 protector and low pressure nozzle. High pressure nozzle is NOT included. Made in Germany. For use when high and low pressures are needed.

For example, spraying cleaning agents with low pressure through an injector valve and then cleaning with high pressure. Lance 15° bended with molded handle, valve ST-54 aside, nozzle protector ST-10 with low pressure nozzle & 1/4" F thread

Flow Switch ST-7 1.5L/Min open 0.4 GPM

ST-7 Flow switch with micro-switch. Switch-on point 0.4 GPM. Mounts in any position horizontal or vertical.

SPECIFICATION:

-Maximum pressure: 5000 psi

-Minimum flow rate: 0.4 GPM

-Maximum flow rate: 12 GPM

-Temperature: 176°F

-Input : 3/8 F

-Outlet: 3/8 F

-Housing: Brass

-Brass reed switch cord length: 47"

-Contact: 10A-250 V

-International protection rating: IP 65

Annovi Reverberi  seal Kit 1857 for 3 pistons Pump RK, RKA, RKV series 138

Consists of:

• O'ring x3
• low pressure(suction) seal x3
• high pressure seal x3
• Seal kit for 3 pistons

St - 2000 is a extreme heavy duty industrial pressure washer gun.The valve body and connectors are corrosion-resistant. The trigger is equipped with a safety lock.

Maximum pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: 3/8 F
Outlet: 1/4 F
Housing: forged brass

ST-458.1 Orifice size 07 Pink. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-458
Nozzle orifice: 07 Pink
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F

1701864 A&R valve repair kit 1864 for pump HXM, XT, XM, Ser. Blitz, X-PRO,KB, Hot, 6,7,9, 132, 178 (1269050)

Valve set for Annovi Reverberi HXM, XT,XM Series blitz, KB, x-pro, 6,7,9, 132, 178. A&R part number (1269050). Valve kit number 1864.

Consists of:

-6 Valves

-6 O-rings

Connection for spray guns with coupling KW. Famous quick coupling system for accessories, quicker to connect and disconnect lance, reducing downtime.(KEW, Nilfisk-Alto) For lances moulded handles. Installation recommendation: Seal with liquid thread sealant only.

Material: stainless steel
Temperature: 300°F
Input connector: Coupling KW
Outlet: 1/4" F

ST-458.1 Orifice size 05 Black. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-458
Nozzle orifice: 05 Black
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F