ST-49.3 mini rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Hardened Ss. Made in Germany
FEATURES:
-Cleaning of deposits
-Cleaning of grease, fat, and other various deposits
-Cleaning of heat exchangers
-Ideal for cleaning or flushing out pipes as well as adjoining lateral pipes at any angle
-Only small pump capacities required
-2 rotating radial jets (90 °) to the pipe wall for best cleaning results
-2 rotating rear jets (45 °) for forward thrust and flushing away of the waster material. suitable for pipes from 0.55" - 2"
SPECIFICATION:
-Maximum pressure: 7250psi
-Input: 1/8” F
-Housing: Hardened Stainless Steel
-Ports: 2 rear jets, 2 side jets
-Nozzle size: 05
Data sheet
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 06. Female 3/8. Material Ss and brass. Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 4”-8” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 1”-3” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
Interpump/general pump seal Kit 127 d18 for EZ pumps
Consists of:
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 055. Female 1/4. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Without centric hole, very good cleaning effect due to rotating nozzle jets.
Connection for spray guns with coupling KW. Famous quick coupling system for accessories, quicker to connect and disconnect lance, reducing downtime.(KEW, Nilfisk-Alto) For lances moulded handles. Installation recommendation: Seal with liquid thread sealant only.
Material: stainless steel
Temperature: 300°F
Input connector: Coupling KW
Outlet: 1/4" F
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 045. Female 1/8. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 1”-3” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
ST-40 Quick screw couplings M22fX1,5:3/8F. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 3/8" F
Housing: brass/plastic
Height 45 mm
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 05
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
Suttner ST-6 Flow Switch, All position (Horizontal or Vertical) Spring assisted brass magnet. Made in Germany
FEATURES:
-Horizontal or vertical mount
-Easy brass reed switch replacement.
SPECIFICATION:
-Max. Pressure: 5,070 PSI/350 bar.
-Min. Pressure: 75 PSI
-Max. Flow Rate: 8 GPM/ 30 ltr.
-Min. Flow Rate: 1 GPM
-Max Voltage: 250 V
-Max Current: 1 Amps
-Max: Fluid Temperature: 180° F/ 80 ° C
-Cable Length: 47.0 in/ 1200 mm.
-Inlet & Outlet: 3/8 MNPT
-Housing: Forged Brass
Nozzle protector. It's made out of soft Rubber which protects sensitive surfaces against damage. It also has a zinc-plated body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 5800 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Zinc-plated steel
Protection material: Rubber
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is :3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 04
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
Suttner ST 73.1 High flow foam injector lance with large 64 oz. Bottle, Stainless steel Integrated Chemical Injector size 1.8, 1/4" F Inlet. Convenient and portable for more effective foam cleaning for Industry, Agriculture, Atuomotive/Fleet and institutional applications!
The ST-73 foam lance is fitted with an interchangeable injector nozzle and a foaming pad. By turning an adjustable grip handle the concentration of foaming agent in the water can be adjusted.
Pressure 1000 - 3625 PSI
Flow Rate 3.4 - up to 8 GPM
Max Temp 175° F
Inlet 1/4" Female
Bottle 64 oz.
Weight 1.20 lb
P.A. Unloader pressure Regulation valve VB 85/280 Blue Spring, knob is not included.
SPECIFICATION:
-Maximum pressure: 4500 psi
-Working rated pressure: 4050 psi
-Inlet 1/2" F
-Outlet 1/2" F
-Bypass 1/2" F
-Maximum flow rate: 21 GPM
-Rated temperature: 195°F
-Housing: forged brass
-Material: brass
-Manufacturer: PA
Repair kit nozzle head for Suttner ST-72 Stainless Steel Foam Lance. Stainless steel construction ideal for food grade applications.
Specifications
Nozzle head without orifice
Input 1/4" FPT
Output 3/8" FPT
Maximum Temperature 300° F
Minimum Temperature 41° F
Quick Screw Coupling (nipple) M22X1,5:1/4"M
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 M
Outlet: 1/4 M
Housing: brass
Height 29 mm
