ST-35 Water Intake Suction Foot Filter (Inlet 3/4" - 1", 19-25 mm, hose barb)

ST-49 non-rotating sewer cleaning Grease ball nozzle. Female 1/4 8x06R. Ss hardened. Made in Germany

The Grease ball features 8 rear jets (0.6 mm) for extreme thrust and highest wall coverage of the pipe. Designed for the ability to clean grease off the sidewall of pipes but has proven to be great on root chokes too. Completely spherical shape. Nozzle drilling as stepped bore for best protection against mechanical impact. Good for 2”-6” inch lines.

Suttner ST-60.1 Foam Injector for use with Suttner ST-72 foam lances. Injector without metering valve, no suction hose, no filter.

Can also be used as low pressure injector.

Minininum 2 Bar

Maximum 2 Bar

Output of Approx. 150l/h

Mixing of chemicals approximately 0 - 11.5%

Suttner ST-6 Flow Switch, All position (Horizontal or Vertical) Spring assisted brass magnet. Made in Germany

FEATURES:

-Horizontal or vertical mount

-Easy brass reed switch replacement.

SPECIFICATION:

-Max. Pressure: 5,070 PSI/350 bar.

-Min. Pressure: 75 PSI

-Max. Flow Rate: 8 GPM/ 30 ltr.

-Min. Flow Rate: 1 GPM

-Max Voltage: 250 V

-Max Current: 1 Amps

-Max: Fluid Temperature: 180° F/ 80 ° C

-Cable Length: 47.0 in/ 1200 mm.

-Inlet & Outlet: 3/8 MNPT

-Housing: Forged Brass

ST-458.1 Orifice size 06 Red. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-458
Nozzle orifice: 06 Red
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F

Lance Nozzle protector for Nilfisk WAP. Made out of soft plastic which protects sensitive surface against damage. The nozzle protector is suitable for cold and hot water applications in the car wash and agriculture. Suitable for Nilfisk WAP nozzle with hexagon 13+14, 1/8" M NPT.

Maximum Pressure 5800 PSI

Rated Temperature 300° F

Protection Material Plastic

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is :3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 04
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 05 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel

Nozzle protector. It's made out of soft Rubber which protects sensitive surfaces against damage. It also has a zinc-plated body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture. Suitable for nozzles 1/4" M NPT.

Maximum pressure: 5800 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Zinc-plated steel
Protection material: Rubber

Suttner Pressure Switch ST-7.1 BLACK 40 bar/580 psi for Pressure Washer. Made in GERMANY.

SPECIFICATION:

-Operating (start up) pressure: 40 bar/ 580 psi

-Rated pressure: 300bar/ 4350psi

-Rated temperature: 90C/ 194F

-Max Voltage: 250V

-Max Current strength: 10.1A

-Electrical Insulation rating: 65 IP

-Material: Brass

-Color: Black

-Inlet: 1/4” M

-Cable length: 950mm/ 37 Inches

ST-456 Orifice size 06 Red. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-456
Nozzle orifice: 06 Red
Spray angle 20°
Pressure range: 2900 - 5076 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
Spray angle: 20°

Suttner ST-261 unloader valve without chemical injector max. pressure 3,625 PSI. Working components constructed of high-grade stainless steel. PTFE and Viton seals for maximum heat and chemical resistance. Straight flow-through design minimizes pressure loss through valve. Adjustable valve allows limit setting on both maximum and minimum pressures. Internal bypass valve can be easily accessed and repaired without removing unloader from unit.

Maximum pressure: 3625 psi
Minimum pressure: 500 psi
Maximum flow rate: 8 GPM
Temperature: 176°F
Input connector: 3/8 F
Outlet: 3/8 F
By pass: 1/4 F
Housing: forged brass

Quick Screw Coupling (nipple) Brass suitable for karcher M22mX1,5:3/8"F

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 3/8" F

Housing: brass

Height 29 mm

ST-357.1 Orifice size 055 light blue . Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-357
Nozzle orifice: 055 Light blue
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F

Interpump/general pump seal Kit 127 d18 for EZ pumps

Consists of:

• support ring x3
• low pressure(suction) seal x3
• high pressure seal x3
• Seal kit for 3 pistons

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 05 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel

Foam injector lance with regulator and bottle. The new LS3, now with vertical nozzle. Nozzle size 1.25.

Inlet 1/4 Bsp F
Pressure 160 bar - 16 MPa - 2300 psi
Permissible Pressure 180 bar - 18 MPa - 2600 psi
Rated Flow Rate 12 l/min - 3.2 USGpm
Rated Temperature 60 °C - 140 °F
Tank 1 L - 0.264 USg