Pressure Switch ST-7.1 RED 362psi

Quick Screw Coupling (nipple) M22X1,5:1/4"M 

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 1/4 M

Housing: brass

Height 29 mm

1701864 A&R valve repair kit 1864 for pump HXM, XT, XM, Ser. Blitz, X-PRO,KB, Hot, 6,7,9, 132, 178 (1269050)

Valve set for Annovi Reverberi HXM, XT,XM Series blitz, KB, x-pro, 6,7,9, 132, 178. A&R part number (1269050). Valve kit number 1864.

Consists of:

-6 Valves

-6 O-rings

ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Ss and brass . Made in Germany

Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 1”-3” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.

Interpump/General pump Valve Kit 123 for pumps EZ, PP, TC, TP, TX.

Consists of:

• 6 valves
• 6 o'rings
• Kit 123 valve set

ST-357.1 Orifice size 04 Brown. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-357
Nozzle orifice: 04 Brown
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F

Suttner ST-60.1 Foam Injector for use with Suttner ST-72 foam lances. Injector without metering valve, no suction hose, no filter.

Can also be used as low pressure injector.

Minininum 2 Bar

Maximum 2 Bar

Output of Approx. 150l/h

Mixing of chemicals approximately 0 - 11.5%

Suttner Pressure Switch ST-7.1 BLACK 40 bar/580 psi for Pressure Washer. Made in GERMANY.

SPECIFICATION:

-Operating (start up) pressure: 40 bar/ 580 psi

-Rated pressure: 300bar/ 4350psi

-Rated temperature: 90C/ 194F

-Max Voltage: 250V

-Max Current strength: 10.1A

-Electrical Insulation rating: 65 IP

-Material: Brass

-Color: Black

-Inlet: 1/4” M

-Cable length: 950mm/ 37 Inches

P.A. Unloader pressure Regulation valve VB 85/280 Blue Spring, knob is not included.

SPECIFICATION:

-Maximum pressure: 4500 psi

-Working rated pressure: 4050 psi

-Inlet 1/2" F

-Outlet 1/2" F

-Bypass 1/2" F

-Maximum flow rate: 21 GPM

-Rated temperature: 195°F

-Housing: forged brass

-Material: brass

-Manufacturer: PA

Metering valve, regular kit for ST-60.1 foam injector. Hose tail 6mm. Made in Germany. Suitable for all Suttner injectors ST-60, ST-60.1, ST-62.

Maximum Pressure 3625 PSI / 250 Bar

Maximum Temperature 140° F

Material Plastic

Hose tail 6mm/0.24 in

Quick Screw Coupling (nipple) Brass suitable for karcher M22mX1,5:3/8"F

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 3/8" F

Housing: brass

Height 29 mm

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 06 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel

ST-10 is 2 component nozzle protector. Made out of hard plastic and soft edge protecting sensitive surfaces against damage . Stainless steel body. The nozzle protector suitable for cold and hot water applications in the car wash, agriculture, food industry. ST-10 is unimpeachable, protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/8" M NPT.

Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/8 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge

Suttner ST-54 Stainless Steel 38" Molded Handle,Twin lance. 15 degrees bended input 1/4"MPT, 2 outlets 1/4"F with nozzle ST-10 protector and low pressure nozzle. High pressure nozzle is NOT included. Made in Germany. For use when high and low pressures are needed.

For example, spraying cleaning agents with low pressure through an injector valve and then cleaning with high pressure. Lance 15° bended with molded handle, valve ST-54 aside, nozzle protector ST-10 with low pressure nozzle & 1/4" F thread

Suitable for all Suttner injectors ST-60, ST-60.1, ST-62. Hose tail 6mm chemical check valve.

Maximum Pressure 3625 PSI / 250 Bar

Maximum Temperature 140° F / 60° C

Material Brass

Hose Tail 6mm/0.24 in

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 045 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel

ST-1500 is a most popular professional spray gun in the market.The grip housing is from impact-resistant plastic. The valve body and connectors are corrosion-resistant. The trigger is equipped with a safety lock.

Maximum pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: 3/8 F
Outlet: 1/4 F
Housing: forged brass