ST-49.3 mini rotating sewer cleaning nozzle. Nozzle size 07. Female 1/8. Material Hardened Ss. Made in Germany
FEATURES:
-Cleaning of deposits
-Cleaning of grease, fat, and other various deposits
-Cleaning of heat exchangers
-Ideal for cleaning or flushing out pipes as well as adjoining lateral pipes at any angle
-Only small pump capacities required
-2 rotating radial jets (90°) to the pipe wall for best cleaning results
-2 rotating rear jets (45°) for forward thrust and flushing ways of the waste material. Suitable for pipes from 0.55" - 2"
SPECIFICATION:
-Maximum pressure: 7250psi
-Input: 1/8” F
-Housing: Hardened Stainless Steel
-Ports: 2 rear jets, 2 side jets
-Nozzle size: 07
Data sheet
ST-40 Quick screw couplings M22fX1,5:3/8F. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 3/8" F
Housing: brass/plastic
Height 45 mm
Quick Screw Coupling (nipple) M22X1,5:3/3"M
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 M
Outlet: 3/8" M
Housing: brass
Height 29 mm
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 045. Female 1/8. Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 1”-3” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 1/4. 3x0.8 Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Without centric hole, very good cleaning effect due to rotating nozzle jets.
The ST-2300 is a professional high pressure cleaning gun (hot/cold water). The grip housing is from an impact-resistant plastic. The valve body and connectors are both corrosion-resistant. The trigger is equipped with a safety lock and rotating swivel joint that the high pressure hose cannot be turned so as to unscrew the connection between high pressure hose and spray gun a swivel joint may be used. By means of this swivel joint the gun may be turned slightly when in an unpressured state in relation to the hose. With increasing pressure the swivel joint becomes increasingly difficult to turn.
Maximum pressure: 4500 psi
Recommended pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: swivel 3/8 F
Outlet: connector 1/4 F
Housing: forged brass
St - 2000 is a extreme heavy duty industrial pressure washer gun.The valve body and connectors are corrosion-resistant. The trigger is equipped with a safety lock.
Maximum pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: 3/8 F
Outlet: 1/4 F
Housing: forged brass
Foam injector lance with regulator and bottle. The new LS3, now with vertical nozzle. Nozzle size 1.25.
Inlet 1/4 Bsp F
Pressure 160 bar - 16 MPa - 2300 psi
Permissible Pressure 180 bar - 18 MPa - 2600 psi
Rated Flow Rate 12 l/min - 3.2 USGpm
Rated Temperature 60 °C - 140 °F
Tank 1 L - 0.264 USg
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 05
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 055
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
Valve set for Annovi Reverberi RK Series 138, 228. A&R part number (1389051).Valve kit number 2864.
Consists of:
Suttner ST-72 Stainless Steel 24" FOAM LANCE, 2.9-3.96 GPM, 2.3 ORIFICE YELLOW COLLAR.
In conjunction with a spray gun and upstream or downstream injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction ideal for food grade applications.
FEATURES:
-Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream.
-Wet foam allows more efficient use of chemical
-More durable than conventional foamers
-Color orifice indicator on handle end
-A foam injector is required
SPECIFICATION:
-Orifice: 2.3 Yellow Dot
-Flow Rates: 2.90 to 3.96 GPM
-Input: 1/4" FPT
-Length: 24"
-Temperature: 300 F maximum, 41 F minimum
-Pressure: 900 PSI maximum
Suttner ST-85 Stainless Steel 38" molded handle Push and Pull lance. Input 1/4"FPT, outlets 1/4"FPT with nozzle ST-10 protector. High pressure nozzle and side handle is NOT included. Made in Germany.
Especially designed for cleaning of places which are difficult to access such as containers, gutters, roofs, underneath fender walls, under vehicles, and heavy equipment. Lance variable adjustment of spraying angle from 20° to 140°. ST-85 Push & Pull lance with nozzle protector ST-10 without high pressure nozzle.
ST-357.1 Orifice size 05 Black. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-357
Nozzle orifice: 05 Black
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
ST-40 Quick Screw Coupling M22X1,5F:1/4 F. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 1/4" F
Housing: brass/plastic
Height 45 mm
ST-5 Flow switch (grey universal). Mounts in horizontal or vertical position (any position). Magnet with hole.
Maximum pressure: 5076 psi
Minimum pressure: 75 psi
Minimum flow rate: 1 GPM
Maximum flow rate: 7.8 GPM
Temperature: 180°F
Input : 3/8 F
Outlet: 3/8 F
Housing: brass
Brass reed switch cord length: 47"
Contact: 1A-250 V
ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Stainless steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.
Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge
