Suttner ST-007 Stainless Steel 47" Molded Handle Lance

Quick Screw Coupling (nipple) Brass suitable for karcher M22mX1,5:3/8"F

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 3/8" F

Housing: brass

Height 29 mm

1702747 A&R Seal Kit 2747 for 3 pistons, Pump XM, Series X-Pro, 9, 178

Consists of:

-O-ring X3

-Low pressure (suction) seal X3

-High pressure seal X3

-Seal kit for 3 pistons

ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 1/4. 3x0.8 Material Ss and brass . Made in Germany

Suttner rotating nozzle for sewer cleaning ST-49.1. Without centric hole, very good cleaning effect due to rotating nozzle jets.

Suttner ST-007 Stainless Steel 39" molded handle lance. Input & output 1/4" Made in Germany.

Most popular lance for cold or hot water applications. Suitable when using corrosive chemicals

Unloader valve/Pressure regulation valve VB-7/3. Brass valve body. Fits CAT 4SF pumps and other pumps.

Maximum pressure: 3625 psi
Working rated pressure: 3200 psi
Maximum flow rate: 8 GPM
Rated temperature: 195°F
Input connector: 3/8 M
Outlet: 3/8 F
By pass: 3/8 F
Pressure gauge outlet: 1/4 F
Housing: forged brass

ST-10 is a 2 component nozzle protector. It's made out of hard plastic and has soft edge which protects sensitive surfaces against damage. It also has a Stainless steel body. The nozzle protector is suitable for cold and hot water applications in the car wash, agriculture, and food industry. ST-10 is unimpeachable, it protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/4" M NPT.

Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/4 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge

Suttner ST-72 Stainless Steel 24" FOAM LANCE, 2.9-3.96 GPM, 2.3 ORIFICE YELLOW COLLAR.

In conjunction with a spray gun and upstream or downstream injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction ideal for food grade applications.

FEATURES:

-Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream.

-Wet foam allows more efficient use of chemical

-More durable than conventional foamers

-Color orifice indicator on handle end

-A foam injector is required

SPECIFICATION:

-Orifice: 2.3 Yellow Dot

-Flow Rates: 2.90 to 3.96 GPM

-Input: 1/4" FPT

-Length: 24"

-Temperature: 300 F maximum, 41 F minimum

-Pressure: 900 PSI maximum

ST-5 Flow switch (grey universal). Mounts in horizontal or vertical position (any position). Magnet with hole.

Maximum pressure: 5076 psi
Minimum pressure: 75 psi
Minimum flow rate: 1 GPM
Maximum flow rate: 7.8 GPM
Temperature: 180°F
Input : 3/8 F
Outlet: 3/8 F
Housing: brass
Brass reed switch cord length: 47"
Contact: 1A-250 V

ST- 2300 Relief valve intended for use on water-operated high-pressure systems such as high-pressure cleaners or water heaters. Adjustable pressure.Stainless steel ball and valve seat.

Seal possible.

Maximum pressure: 5076 psi
Maximum flow rate: 8 GPM
Temperature: 200°F
Input : 3/8 F
Outlet: 3/8 F
Housing material: Forged brass

PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is :3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.

Type: PMEG
Nozzle orifice: 045 
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel

Suttner ST-85 Stainless Steel 38" molded handle Push and Pull lance. Input 1/4"FPT, outlets 1/4"FPT with nozzle ST-10 protector. High pressure nozzle and side handle is NOT included. Made in Germany.

Especially designed for cleaning of places which are difficult to access such as containers, gutters, roofs, underneath fender walls, under vehicles, and heavy equipment. Lance variable adjustment of spraying angle from 20° to 140°. ST-85 Push & Pull lance with nozzle protector ST-10 without high pressure nozzle.

ST-458.1 Orifice size 07 Pink. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.

Type: ST-458
Nozzle orifice: 07 Pink
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F

ST-49.1 rotating sewer cleaning nozzle. Nozzle size 045. Female 1/8. Material Ss and brass . Made in Germany

Suttner rotating nozzle for sewer cleaning ST-49.1. Ideal for 1”-3” lines. Without centric hole, very good cleaning effect due to rotating nozzle jets.

Annovi Reverberi  seal Kit 1857 for 3 pistons Pump RK, RKA, RKV series 138

Consists of:

• O'ring x3
• low pressure(suction) seal x3
• high pressure seal x3
• Seal kit for 3 pistons

ST-1500 is a most popular professional spray gun in the market.The grip housing is from impact-resistant plastic. The valve body and connectors are corrosion-resistant. The trigger is equipped with a safety lock.

Maximum pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: 3/8 F
Outlet: 1/4 F
Housing: forged brass

Quick Screw Coupling (nipple) M22X1,5:3/3"M 

Maximum pressure: 5800 psi

Temperature: 300°F

Input: M22 M 

Outlet: 3/8" M

Housing: brass

Height 29 mm