PA Fine Water Filter 355 Microns. Chemical resistant detergent strainer. Without check valve. Stainless steel screen with brazen bottom weight. Inlet barb 6-8mm. Made in Italy.
Without check valve
Corrosion plastic body with stainless steel screen
Stepped 0.24/6 - 0.32/8 in/mm hose barb
Fine filter 51 mesh 355 Microns
Height 55mm
Diameter 22mm
Temperature 104° F
Weight 0.7 oz
ST-31 Intake chemical strainer without check valve. Strainer prevents debris from entering and destroying the components. Hose barb 1/4 -1/8. Internal stainless steel weight keep chemical strainer in the bottom of the container.
Housing: plastic
Weight: stainless steel
Diameter: 20 mm / 0.8"
Length: 75 mm / 3"
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is :3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 045
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/8 "M.
Housing: Hardened stainless steel
Professional gun with patented LTF technology. (LTF - Low Trigger Force 90% reduced holding force and 40% reduced trigger force agains usual market guns).Gun with coupling ST-3100 (lance not including). Stainless steel. Suitable for e.g. huge water amounts in the food industry. PEEK valve cone enables use in low pressure.Made out of plastics to come into contact with foodstuffs.Especially disigned for applicationsin the food industry.
Maximum pressure: 1800 psi
Maximum flow rate: 21 GPM
Temperature: 300°F
Input connector: 1/2 "F swivel
Outlet: ST-3100 coupling
Housing: Stainless steel
PR-5 Blue pressure switch is a fluid operating electro-mechanical device, which, upon reaching a pre-set (start-up)pressure 15 bar/218 PSI, opens or closes an electrical control contact . Microswitch with very high resistance openings. Considerable resistance to high current values. Compact overall dimension. Three core cable.
Maximum pressure: 5076 psi
Rated working pressure: 3650 psi
Minimum pressure: 218 psi
Temperature: 167°F
Input : 1/4 F
Housing material: brass
Cord length: 37"
Max Curr./V. strength Contact: 5A-250 V
International protection rating: IP 65
Suttner ST-261 unloader valve without chemical injector max. pressure 3,625 PSI. Working components constructed of high-grade stainless steel. PTFE and Viton seals for maximum heat and chemical resistance. Straight flow-through design minimizes pressure loss through valve. Adjustable valve allows limit setting on both maximum and minimum pressures. Internal bypass valve can be easily accessed and repaired without removing unloader from unit.
Maximum pressure: 3625 psi
Minimum pressure: 500 psi
Maximum flow rate: 8 GPM
Temperature: 176°F
Input connector: 3/8 F
Outlet: 3/8 F
By pass: 1/4 F
Housing: forged brass
1702747 A&R Seal Kit 2747 for 3 pistons, Pump XM, Series X-Pro, 9, 178
Consists of:
-O-ring X3
-Low pressure (suction) seal X3
-High pressure seal X3
-Seal kit for 3 pistons
ST-7 Flow switch with micro-switch. Switch-on point 1.1GPM. Mounts in any position horizontal or vertical.
Maximum pressure: 5000 psi
Minimum flow rate: 1.1 GPM
Maximum flow rate: 12 GPM
Temperature: 176°F
Input : 3/8 F
Outlet: 3/8 F
Housing: brass
Brass reed switch cord length: 47"
Contact: 10A-250 V
International protection rating: IP 65
ST-357.1 Orifice size 06 Red. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-357
Nozzle orifice: 06 Red
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
ST-49 non-rotating sewer cleaning Grease ball nozzle. Female 1/4 8x06R. Ss hardened. Made in Germany
The Grease ball features 8 rear jets (0.6 mm) for extreme thrust and highest wall coverage of the pipe. Designed for the ability to clean grease off the sidewall of pipes but has proven to be great on root chokes too. Completely spherical shape. Nozzle drilling as stepped bore for best protection against mechanical impact. Good for 2”-6” inch lines.
ST- 2300 Relief valve intended for use on water-operated high-pressure systems such as high-pressure cleaners or water heaters. Adjustable pressure.Stainless steel ball and valve seat.
Seal possible.
Maximum pressure: 5076 psi
Maximum flow rate: 8 GPM
Temperature: 200°F
Input : 3/8 F
Outlet: 3/8 F
Housing material: Forged brass
General Pump Repair Kit 137 - Unloader Repair Kit, For Triplex pumps TX, EZ Series 44, U, UI.
Consists of:
Anti-ext ring 90505200
O-ring 90382000
Sleeve 36323470
O-ring(2) 90357500
Anti-ext ring 90502500
Spacer 36323070
Spring 94748500
Valve 36323151
Valve guide 36322970
O-ring 90360000
Anti-ext ring 90514400
Spherical valve 36319066
Screw 99150900
Seat 36316466
O-ring 701614
Anti-ext ring 90506500
ST-40 Quick screw couplings M22fX1,5:3/8F. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 3/8" F
Housing: brass/plastic
Height 45 mm
Suttner ST-72 Stainless Steel 24" FOAM LANCE, 2.9-3.96 GPM, 2.3 ORIFICE YELLOW COLLAR.
In conjunction with a spray gun and upstream or downstream injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction ideal for food grade applications.
FEATURES:
-Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream.
-Wet foam allows more efficient use of chemical
-More durable than conventional foamers
-Color orifice indicator on handle end
-A foam injector is required
SPECIFICATION:
-Orifice: 2.3 Yellow Dot
-Flow Rates: 2.90 to 3.96 GPM
-Input: 1/4" FPT
-Length: 24"
-Temperature: 300 F maximum, 41 F minimum
-Pressure: 900 PSI maximum
St - 2000 is a extreme heavy duty industrial pressure washer gun.The valve body and connectors are corrosion-resistant. The trigger is equipped with a safety lock.
Maximum pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: 3/8 F
Outlet: 1/4 F
Housing: forged brass
Unloader valve/Pressure regulation valve VB-7/3. Brass valve body. Fits CAT 4SF pumps and other pumps.
Maximum pressure: 3625 psi
Working rated pressure: 3200 psi
Maximum flow rate: 8 GPM
Rated temperature: 195°F
Input connector: 3/8 M
Outlet: 3/8 F
By pass: 3/8 F
Pressure gauge outlet: 1/4 F
Housing: forged brass
ST-10 is 2 component nozzle protector. Made out of hard plastic and soft edge protecting sensitive surfaces against damage . Stainless steel body. The nozzle protector suitable for cold and hot water applications in the car wash, agriculture, food industry. ST-10 is unimpeachable, protects your nozzles and preserves the surfaces to be cleaned at the same time. Suitable for nozzles 1/8" M NPT.
Maximum pressure: 7250 psi
Rated temperature: 300°F
Input: 1/4 F NPT
Outlet: 1/8 F NPT
Housing: Stainless Steel
Protection material: Hard plastic/Soft edge
Water intake suction foot filter ST-35. High flow suction strainer ideal for tank transfer or agricultural markets. Made in Germany.
SPECIFICATION:
-Without Check valve
-Stainless steel spring and screen
-Inlet Stepped 3/4"-1”, 19-25 mm/ hose barb
-Corrosion-resistant heavy impact resistant plastic
-Max temperature: 140°F
-Compatible with all pressure washers
-Brass weighted to hold onto bottom of tank
