ST-49 non- rotating sewer cleaning root ram nozzle. Nozzle size 06. Female 1/4. Material Ss hardened. Made in Germany
The Root ram is equipped with 3 rear jets (30°) for maximum thrust and 3 additional nozzles (45°) right behind its nose for better cleaning results and wall coverage. The nozzle has proven to be ideal on root chokes. Good for 2"-6" lines.
SPECIFICATION:
-Maximum pressure: 7250psi
-Input: 1/4” F
-Housing: Hardened Stainless Steel
-Ports: 1 front jet, 6 rear jets
-Nozzle size: 06
-Flow rate: 7.95 GPM
Data sheet
Suttner repair kit for ST-2300/2600 Pressure washer trigger gun. With instructions inside. Made in Germany.
-Instructions inside
-Fits ST2300/2600/2305/2605
-Kit for repairing Suttner Pressure washer guns
-Manufacturer: Suttner
St-33 Water intake T-strainer filter complete with filter fine core washable (stainless steel and plastic).
Maximum pressure: 87 psi
Maximum flow rate: 13.2 GPM
Temperature: 140°F
Input: 3/4 F
Outlet: 3/4 M
Housing: plastic
Screen material: stainless steel+plastic
Screen Microns: 50
ST-357.1 Orifice size 07 Pink . Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-357
Nozzle orifice: 07 Pink
Spray angle 20°
Pressure range: 1450 - 3625 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
ST-49.1 rotating sewer cleaning nozzle. Nozzle size 05. Female 1/4. 3x0.8 Material Ss and brass . Made in Germany
Suttner rotating nozzle for sewer cleaning ST-49.1. Without centric hole, very good cleaning effect due to rotating nozzle jets.
Suttner Pressure Switch ST-7.1 BLACK 40 bar/580 psi for Pressure Washer. Made in GERMANY.
SPECIFICATION:
-Operating (start up) pressure: 40 bar/ 580 psi
-Rated pressure: 300bar/ 4350psi
-Rated temperature: 90C/ 194F
-Max Voltage: 250V
-Max Current strength: 10.1A
-Electrical Insulation rating: 65 IP
-Material: Brass
-Color: Black
-Inlet: 1/4” M
-Cable length: 950mm/ 37 Inches
ST- 2300 (old type) Relief valve intended for use on water-operated high-pressure systems such as high-pressure cleaners or water heaters.Adjustable pressure.Stainless steel ball and valve seat.
Maximum pressure: 5076 psi
Maximum flow rate: 8 GPM
Temperature: 200°F
Input : 1/4 F
Outlet: 1/4 F
Housing material: Forged brass
ST-40 Quick screw couplings M22fX1,5:3/8F. Suitable for Karcher and more.
Maximum pressure: 5800 psi
Temperature: 300°F
Input: M22 F
Outlet: 3/8" F
Housing: brass/plastic
Height 45 mm
ST-49 non-rotating sewer cleaning Grease ball nozzle. Female 1/4 8x06R. Ss hardened. Made in Germany
The Grease ball features 8 rear jets (0.6 mm) for extreme thrust and highest wall coverage of the pipe. Designed for the ability to clean grease off the sidewall of pipes but has proven to be great on root chokes too. Completely spherical shape. Nozzle drilling as stepped bore for best protection against mechanical impact. Good for 2”-6” inch lines.
ST-458.1 Orifice size 05 Black. Rotating nozzle with ceramic insert. The increased tearing action of the rotating spray is ideal for hard surface applications, such as concrete graffiti cleaning or caked on mud on heavy equipment. Improved materials for longer life. Increases cleaning efficiency as much as 200%.
Type: ST-458
Nozzle orifice: 05 Black
Spray angle 20°
Pressure range: 2900 - 5800 psi
Inlet: 1/4 "F.
Housing: brass
Color of protective cap: Black
Temperature: 212 °F
A&R Ceramic piston kit 2758 pump series RK 228 RK18.20H, RK18.28H D20 Annovi Reverberi part number 1380930. A&R piston 20x40 mm.
Consists of:
-3 pieces
ST-7 Flow switch with micro-switch. Switch-on point 1.1GPM. Mounts in any position horizontal or vertical.
Maximum pressure: 5000 psi
Minimum flow rate: 1.1 GPM
Maximum flow rate: 12 GPM
Temperature: 176°F
Input : 3/8 F
Outlet: 3/8 F
Housing: brass
Brass reed switch cord length: 47"
Contact: 10A-250 V
International protection rating: IP 65
Suttner ST-72 Stainless Steel 24" FOAM LANCE, 2.9-3.96 GPM, 2.3 ORIFICE YELLOW COLLAR.
In conjunction with a spray gun and upstream or downstream injector, allows cleaning agents or disinfectants to be applied evenly over a large surface. Stainless steel construction ideal for food grade applications.
FEATURES:
-Thick foam is produced when air flows through vented injector housing and mixes with water and chemical stream.
-Wet foam allows more efficient use of chemical
-More durable than conventional foamers
-Color orifice indicator on handle end
-A foam injector is required
SPECIFICATION:
-Orifice: 2.3 Yellow Dot
-Flow Rates: 2.90 to 3.96 GPM
-Input: 1/4" FPT
-Length: 24"
-Temperature: 300 F maximum, 41 F minimum
-Pressure: 900 PSI maximum
ST-49.3 mini rotating sewer cleaning nozzle. Nozzle size 05. Female 1/8. Material Hardened Ss. Made in Germany
The ST-2300 is a professional high pressure cleaning gun (hot/cold water). The grip housing is from an impact-resistant plastic. The valve body and connectors are both corrosion-resistant. The trigger is equipped with a safety lock and rotating swivel joint that the high pressure hose cannot be turned so as to unscrew the connection between high pressure hose and spray gun a swivel joint may be used. By means of this swivel joint the gun may be turned slightly when in an unpressured state in relation to the hose. With increasing pressure the swivel joint becomes increasingly difficult to turn.
Maximum pressure: 4500 psi
Recommended pressure: 4000 psi
Maximum flow rate: 12 GPM
Temperature: 300°F
Input connector: swivel 3/8 F
Outlet: connector 1/4 F
Housing: forged brass
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is :3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 04
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
PMEG nozzles is high impact washJet flat spray nozzles are ideal for pressure washing, cleaning and car wash applications. Advantages of Power-MEG nozzles is: 3 time faster, saves up to 60% water, 3 times higher impact. Hardened stainless steel construction provides long wear life and flow control accuracy. Recommended for surface cleaner use. The WashJet product line, however, was designed specifically to operate in high-pressure applications and will provide improved cleaning effectiveness and a better distribution of impact across the entire spray pattern.
Type: PMEG
Nozzle orifice: 055
Spray angle 15°
Pressure range: 300 to 4000 psi (20 to 275 bar)
Inlet: 1/4 "M.
Housing: Hardened stainless steel
